The RFID-Zapper is a gadget to deactivate (i.e. destroy) passive RFID-Tags permanently.
The development-team presently consists of two people (MiniMe and Mahajivana), who had some help from a friend (thank's for that).
Goals are a proof-of-concept and the construction of at least one functioning and appealing prototype, as well as a documentation of the project, so that everyone can build an own RFID-Zapper. Since the project found so much positive resonance, we probably are going to work on some other realizations ot the concept, e.g. building an RFID-Zapper from scratch, without a single-use-camera.
We have to expect to be surrounded by RFID-Tags almost everywhere within the near future, and they will serve many different purposes. The benefits and risks of this technology and it's use are already being discussed. However, there will be atempts to use RFID-Tags to establish constant surveiliance and to further threaten and compromise the privacy of customers (and citizens and even non-citizens, when gouvernments start to use RFID-Tags like the german gouvernment already did).
To defend yourself against such measures, you might want a small, simple and relatively appealing gadget to permanently deactivate RFID-Tags around you, e.g., to deactivate RFID-Tags in recently bought clothes or books without damaging those.
Passive RFID tags have no internal power supply. The minute electrical current induced in the antenna by the incoming radio frequency signal provides just enough power for the CMOS integrated circuit (IC) in the tag to power up and transmit a response.
(Quote from Wikipedia)
There are several ways to deactivate RFID-Tags. One that might be offered by the industries are RFID-deactivators, which will send the RFID-Tag to sleep. A problem with this method is, that it is not permanent, the RFID-Tag can be reactivated (probably without your knowledge). Several ways of permanently deactivating RFID-Tags are know, e.g., cutting off the antenna from the actual microchip or overloading and literally frying the RFID-Tag in a common microwave-oven, which needs to be turned on only for a short period of time. Unfortunately both methods aren't suitable for the destruction of RFID-Tags in clothes: cutting off the antenna would require to damage the piece of cloth, while frying the chips is likely to cause a small but potent flame, which would damage most textiles or even set them on fire.
The RFID-Zapper solves this dilemma. Basically it copies the microwave-oven-method, but in a much smaller scale. It generates a strong electromagnetic field with a coil, which should be placed as near to the target RFID-Tag as possible. The RFID-Tag then will receive a strong shock of energy comparable with an EMP and some part of it will blow, thus deactivating the chip forever.
To keep the costs of the RFID-Zapper as low as possible, we decided to modify the electric component of a singe-use-camera with flash, as can be found almost everywhere. The coil is made from coated copper wire and placed inside the camera exactly where the film has been. Then one end of the coil is soldered to the camera's capacitor, from which we earlier disconnected the flash. The other end of the coil is soldered to a switch, which itself is connected to the capacitor's other terminal. Once everything is tested, the camera can be closed again and henceforth will serve as a RFID-Zapper, destroying RFID-Tags with the power of ordinary batteries.
The original project was finished successfully and introduced at 22C3. Several RFID-Zappers where build at 22C3 in a workshop.
Modification of a single-use-camera with flash has proven to be relatively easy, the capacitor is able to supply enough electrical current.
An old, slightly damaged Camera could also be modified into a RFID-Zapper during the workhop at 22C3.
As far as we know, about 20 working RFID-Zappers were build so far. Only in one case we encountered serious problems, the capacitor seemed to be broken.
By the way: It is possible to carefully (don't expose it to any light) extract the photographic film from the camera for further use. (Most films from single-use-camera's seem to have no DX encoding, so they might be useful for push processing or even pull processing ;-) But don't expect to much from such films, single-use-cameras usually don't come with a high-quality film.
Before we first tried to modify a single-use-camera, we tested the concept on a passive 13,56-MHz-RFID-Tag:
* We are completing the documentation on our project these days. This documentation will contain a construction-manual for the RFID-Zapper and will be published both in german and english. You should be able to find it on this wiki within the next two weeks, we will also place it on several other homepages, including mahajivana's, which hopefully will go online soon and will contain more about this project.
Contact
(This part of this article probably will be longer than the equivalent part in the german article, since english-speaking peoble seem to be more concerned with safety matters and less careful with electric devices ;-)